Crane toilet tanks 18 years ago were 3.5 gal. All that is available today are 1.6 flush. Your old bowl will not flush with less water. It would be less costly to replace the whole toilet with a better toilet. The Kohler wellworth model is a great flushing 1.6 toilet. Now, If you want to replace the tank only, this is what you can do to get the full 3.5 flush. Purchase a new Crane 1.6 Galaxy model tank. ![]() I have a leaking water tank here in Bombay, India. I'm looking for suggestions on how to repair it.The tank is a plastic Sintex water tank.There are cracks around a water pipe running into the side of the tank. When there is a leak from your toilet tank, it could be any of the following reasons: The flush valve is damaged. The flush valve doesn't seal tightly because of built-up mineral deposits. The flapper is worn out. To confirm a leak, simply turn off the tank's water supply, mark the water level, and wait about 30 minutes. A leaking toilet tank can be annoying and wasteful at the same time, learn how to repair it or how to replace a toilet tank to put the matter to rest. You can use easy guidelines or get a plumber to help with a leaking toilet tank. Something must have fallen into the toilet bowl - there is a very small crack/hole that doesn't seem to be letting water out as the water level stays the same - but - I really want to put something over it to seal it. You will have to change the Flush valve with a taller model. Fluidmaster make a replacement with a tall overflow tube #507A. Then replace the fill valve with a Fluidmaster 400A and raise the fill valve to a taller level. Instructions are on the box. Doing this will give you a new 3.5 tank. By the way the govt. Doesn't want you to do this and this I didn't tell you.hehe. Keep in mind that you can't use another brand tank on your Crane bowl. It must be a Crane Galaxy tank. ![]() They should be available at most plumbing wholesale distributors. ***** also carries this line in many areas. Toilet tank lids with only one or two cracks or breaks will fit together with ceramic glue so that the fix is not obvious. If a lid is broken into many small pieces, check around and inside the toilet tank for missing pieces to adhere together. Dear NH: I need some help and couldn't find the answer in your site. Our toilet bowl does not have enough water in it! Yup, a daily mess because it doesn't flush completely most of the time. Please help us!! NJ NJ, If you have a typical residential toilet, there is a flexible rubber or plastic tube that is attached to the inlet valve. • States that don't issue licenses have until November 2018 to put together an OSHA compliant license program or adopt an accredited license program. Call ahead before you take a job there. New york city crane license ct. • New York City issues its own license but accepts some accredited licenses as well. • New Hampshire, Vermont and Maine don't issue licenses yet. It runs to a long, vertical tube in the center of the toilet called the overflow tube. That's it right over the flapper. When you flush the toilet, this tube redirects some water into a vertical pipe to which the rubber flapper is attached. This additional water is what controls the level of the water in the bowl. If this tube is not supplying water. Either because of a defect in the tube such as a kink, defect in the inlet valve itself, or if it has been disconnected or moved. The bowl will have too low a water level for an efficient and thorough flush. If the tube is kinked, try to unkink it or replace it. These tubes occasionally become very stiff and even brittle when the homeowner has used bleach-containing toilet cleaning products in the tank. If you find that there is no water flowing through the tube, even though it is not kinked or blocked, your intake valve probably needs to be replaced. If you have an unusual low flow toilet or some of the older odd brands, this won't be of much help BUT the concept is the same water must somehow get into the bowl as the tank fills so that there is enough water for a proper flush. Many plumbing supply stores are happy to help you troubleshoot unusual toilets as long as you can supply some basic information. Aside from the brand name, useful information is often times stamped onto the inside of the toilet tank lid. You might also want to check the water level in the tank. Is the level of water up to the 'water line' mark? If you can't see a mark, use the overflow tube as a guide. The water level should be about an inch below the top of the overflow tube. ![]() If not, adjust the inlet valve to raise the level. To conserve water, people often install 'displacement' devices in the tank. Water dams, water bags, etc. ![]() ![]() For water conservation. The strength of the flush is affected by these, so if your flush is still balks, remove them. Dear NH, Do you know of a way to repair a broken toilet base? When reseating the toilet I broke the flat portion of the base around the bolthole. Will a heavy duty epoxy work? GJ from Hurst,TX GJ, I can usually come up with a repair or at least offer some hope, but in your case I'm hesitant. Toilets are made from clay, baked and glazed to a smooth finish. Though they appear to be very tough, an abused toilet will break just like a ceramic plate! Sometimes a 'temporary' emergency repair can be made to a cracked bowl or tank (neither of which I recommend). The break you describe is at a high-stress area of the toilet. There is no adhesive that exists today that I would trust to make this repair. Should it re-break when the toilet is being used, severe leakage around the wax seal under the toilet could occur with dire consequences! The break probably occurred because you overtightened the mounting nut, causing the ceramic to crack. Another possibility is that the base already had a slight stress crack that finally gave way during reinstallation. Old toilets are particularly prone to this sort of breakage. Also, if the floor is uneven, the toilet might rock and appear to be loose even though you've completely tightened the bolt. Breakage during installation is the most common toilet installation problem and even happens occasionally to pros. Because the mounting nut never really feels tight, making it too easy to accidentally overtighten it! For future reference, the tightness of toilet mounting nuts is judged by the stability of the toilet, not the apparent tightness of the nut! If the toilet easily turns or 'wiggles' under pressure (either by hand or by actually sitting on it), then it requires a little more tightening. There is one exception. If the floor is slightly uneven (which should be obvious by looking under the base of the toilet) breakage is even more likely since the entire base may not be tightly against the floor! Careful tightening followed by caulking around the toilet base will give sufficient support and stability. Remember, tighten the nuts firmly just not too aggressively! IF YOU ARE DETERMINED TO TRY AN ADHESIVE. My choice would be polyurethane glue. This form of glue is very strong and sticks to almost anything! If anything will work in this circumstance, polyurethane glue is it! Polyurethane glue expands as it dries, so you don't need to slather it on. A thin coat on one side is plenty. The surfaces should be slightly damp.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |